NS-WP86-DIM-LV adopts the most advanced PWM (Pulse Width Modulation) digital dimming technology, especially design for single color led strip. For instance, point source of light, flexible light strip, led modules, led strings and so on. Belong to low-voltage DC power input and output with two interfaces, including V+ is the positive interfaces, the other three for the negative interface. Meanwhile, you can turn on/off, adjust brightness for different lighting effects through full-touch wall panel remote control. In addition, It is convenient to use RJ45 connector to connect the multiple controllers together, and achieve the synchronization function of thousands meters led strips. In theory, they can be connected numerous.

Product Feature

● Designed for single color constant voltage LED lights, Working voltage DC12-24V.

● Three channels output, Max. load current: 3CH*8A; Max. load power: 288W/12V; 576W/24V.

● Adopts full-touch wall panel remote control with fashion appearance, no need line-of-sight. Control range up to 20 meters. The working voltage of wall-panel is AC90-265V.

● Structure/dimension/installation of the wall panel according to the 86-type European standards.

● Memory function, each time power-on reserve the mode which stop in the last power-down.

● Long-press the brightness and speed key can get the fast adjustment, convenient for operation.

● Multiple controllers can work synchronically when connected by network cable through the RJ45 connector, the network cable between 2 ports up to 80 meters.

● Warranty of this product is one year, exclude the artificial situation of damaged or overload working.

Technical Parameters

Controller

Remote control

Interface Specifications

Connection:V+→COM,CH1→V-,CH2→V-,CH3→V-；

Direction for use

● Connect the load wire at first, followed by the power wire; Please ensure short circuit can not occur between wires before turning on the power；

● Adopts RF full touch wall-panel remote control, with one dimming ring and 5 function buttons.

● The signal light flash-- represents the signal has been sent well;

The function of buttons are shown as below:

3 modes in total as below:

Tips: Receiver can be controlled by any one the same remote as factory default; the wall-panel remote control delivered with unique RF code as factory default; if unique-control is needed, please matching the code before installation and using.

Matching code operation

If unique-control or new-coded-remote is needed, pairing the remote and the receiver as below operation instruction before using:

1. Step 1: Pressing key “mode” and hold on, power on the controller, the load LEDs will be 50% brightness white as responding.

2. Step 2: Continuously to press the key “ON“ for 3 times within 5 seconds after step 1 ,the brightness of LEDs will change from 25% -10% as responding.

3. Code learning successfully, the LEDs will be back to the status before the power off, and the receiver only can be control by the remote.

4. If not, please re-operate from step 1 to 2.

Clear code operation

Back to factory default, receiver can be controlled by any one the same remote control.

1. Step 1: Pressing key “Mode” and hold on, power on the controller, the load LEDs will be 50% brightness white as responding.

2. Step 2: Continuously to press “Speed/Brightness -“ 3 times within 5 seconds after step 1 ,the brightness of LEDs will change from 25% -10% as responding.

3. Code clearing successfully, the LEDs will be back to the status before the power off, and the receiver can be controlled by any remote control(any one the same remote control can be used to clear the code).

4. If not, please re-operate from step 1 to 2.

Wall-panel Installation instruction

Step 1: Fixing the bottom cover into the wall;	Step 2:Fixing the metal frame into the bottom cover with screws( projecting part upward )
Step 3: Pressing the wall-panel into the metal frame, after connecting well the input and output wires.

Typical Applications

Power and LED’s connection diagram:

Conjunction diagram :

Product information for placing order

Newstar LED Co., Limited Established in 2009, covering an area of 2100 square meters, we now have over 50 employees, we are a professional manufacturer and exporter that is concerned with the design, development and production of LED lighting products. We are located in Shenzhen city, with convenient transportation access. All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.

Newstar has a well-trained team including full experienced technicians and salesman, "product quality and service foremost" is our main goal. An annual sales figure that exceeds USD15,000,000 and 80% of our products exported to more than 100 countries. More and more customers are continually choosing Newstar for our excellent quality and service, your OEM or ODM are welcomed

The main products of our company: led flood light, led high bay light, led panel, led strip, led downlight, led tube, and so on, all of which are widely used in commercial lighting decoration, indoor and outdoor using, home and decoration, bus and train station using, advertising and cabinet Lighting.

Quality Control: Newstar’s operation strictly follows the ISO9001 standard. All of our products have CE, ROHS certificates. The key material we source from Samsung, Cree, Bridgelux, Epistar, MeanWell to assure a steady and top-grade quality.

As a globally operating manufacturers, we also strongly encourage socially and environmentally authoritative energy-saving policies around the world - as well as sponsoring art and beauty at home and world! Join us to achieve the mutual benefit, and let's make people's life brighter and more colorful!